Welcome Guest ( Login | Register )



All times are UTC - 7 hours [ DST ]



Post new topic Reply to topic  [ 4 posts ] 
Author Message
 Post subject: Connection Problems FX3U ENET Driver with TCP
PostPosted: Tue Nov 19, 2013 4:44 am 

Joined: Tue Nov 19, 2013 3:44 am
Posts: 1

Offline
Hello,

I´m having problems connecting a FX3GE PLC through Ethernet over the ADP module to a iX T7A Panel via TCP.
I´m using the FX3U-ENET driver with mixed read protocol.

The same setup works just fine over UDP but with TCP it immediatly generates an error on the PLC´s ADP module which says "A specific command or subcommand is wrong"

In the Ethernet Diagnostics of the PLC i can see the IP adress and the port from which the request came, in this case the panel, but thats about it.

Am I missing any settings or is the driver not working propely ?


Attachments:
FX3U-ENET_2.png
FX3U-ENET_2.png [ 36.47 KiB | Viewed 8685 times ]
FX3U-ENET_1.png
FX3U-ENET_1.png [ 17.07 KiB | Viewed 8685 times ]
 Profile  
 
 Post subject: Re: Connection Problems FX3U ENET Driver with TCP
PostPosted: Fri Dec 06, 2013 3:21 am 

Joined: Wed Jun 27, 2012 1:17 am
Posts: 73
Location: CZ

Offline
Hi Roman,

Problem what you have is, that FX3GE has Ethernet on left ( it's the same module as FX3U-ENET-ADP - only is integrated in PLC) so you need change the port on TCP. It's not 5551 but it's 5556

Attachment:
Image2.png
Image2.png [ 16.2 KiB | Viewed 8680 times ]


There is help in setting where you can read it. Make sure that you have the latest version of friver.

Attachment:
Image1.jpg
Image1.jpg [ 56.15 KiB | Viewed 8680 times ]



BR
JohnCZ


 Profile  
 
 Post subject: Re: Connection Problems FX3U ENET Driver with TCP
PostPosted: Sun Apr 13, 2014 7:47 am 

Joined: Sun Apr 13, 2014 7:43 am
Posts: 1

Offline
Hi JohnCZ,

Yes It works with port no. 5556.
But where can you read about this?
Could not se it in the Help file, and only because of your reply to Roman.

Best regards
Dariusch


 Profile  
 
 Post subject: Re: Connection Problems FX3U ENET Driver with TCP
PostPosted: Wed Apr 23, 2014 1:48 am 

Joined: Wed Jun 27, 2012 1:17 am
Posts: 73
Location: CZ

Offline
Hi,
Dariusch

Sorry for my bad navigations, I work primarily with mitsubishi. This port is used for communication with the module in other software. This port is mentioned in the manual for the FX3U-ENET-ADP user manual not in iX Help ( see picture ). Beijers has not integrated FX3GE or FX3U-ENET-ADP in to the help file yet( in IX HELP is mention that you need to see hw manual ), because it's relative new product ;) but thats not problem for Beijer because it's realy good hw.

Attachment:
File comment: From iX Help
FX3U-ENET-ADP User manual.PNG
FX3U-ENET-ADP User manual.PNG [ 11.16 KiB | Viewed 8244 times ]


Attachment:
File comment: From section 9.3 in User manual
FX3U-ENET-ADP User manual.PNG
FX3U-ENET-ADP User manual.PNG [ 12.81 KiB | Viewed 8244 times ]


BR
JohnCZ


 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 4 posts ] 

All times are UTC - 7 hours [ DST ]


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron