Welcome Guest ( Login | Register )



All times are UTC - 7 hours [ DST ]



Post new topic Reply to topic  [ 1 post ] 
Author Message
 Post subject: Loading Firmware to an iX Panel TxA or TxB
PostPosted: Thu Jan 24, 2013 5:33 pm 
User avatar

Joined: Fri Jul 15, 2011 3:21 pm
Posts: 214

Offline
Loading Firmware to an iX Panel TxA or TxB

Attachment:
Snap 2013-01-24 at 16.21.59.png
Snap 2013-01-24 at 16.21.59.png [ 40.1 KiB | Viewed 6362 times ]


Download the file IML_TxB_bX or IML_TxA_bX where X is the version number for the firmware. If the file is a .ZIP, unzip the file before opening.

Go to control panel and disable the primary Ethernet card so the PC has only one active Ethernet port.

Attachment:
Snap 2013-01-24 at 16.25.01.png
Snap 2013-01-24 at 16.25.01.png [ 75.1 KiB | Viewed 6362 times ]


Once only one Ethernet port is enabled, make sure it is configured to use a static IP address instead of DHCP.

Attachment:
Snap 2013-01-24 at 16.25.15.png
Snap 2013-01-24 at 16.25.15.png [ 187.96 KiB | Viewed 6362 times ]


Use a cross-over cable to connect directly from the PC to the terminal.

Before starting the program, verify communication with the iX Panel over Ethernet. Use the command line and ping the terminal as shown in the “Ethernet Trouble Shooting” section.

Power off the iX Panel TxA or TxB. Press the touchscreen and apply power. When the screen appears that says “Enter Update Mode?”, touch the screen to enter update mode.

Open the file IML_TxB_bX.exe or IML_TxA_bX.exe and press “Next >”.

Attachment:
Snap 2013-01-24 at 16.25.30.png
Snap 2013-01-24 at 16.25.30.png [ 90.89 KiB | Viewed 6362 times ]


Press “Next >” again.

Attachment:
Snap 2013-01-24 at 16.25.50.png
Snap 2013-01-24 at 16.25.50.png [ 68.47 KiB | Viewed 6362 times ]


If everything was setup correctly before, your terminals MAC address will be displayed as an option the drop down list. Select the MAC address and press “Upgrade >”.

Attachment:
Snap 2013-01-24 at 16.26.08.png
Snap 2013-01-24 at 16.26.08.png [ 76.6 KiB | Viewed 6362 times ]


If you encounter this error message, then make sure you are using a private Ethernet port and a cross-over cable. Restart the program, restart the terminal, verify you can ping the terminal, put the terminal into update mode and try again.

Attachment:
Snap 2013-01-24 at 16.26.22.png
Snap 2013-01-24 at 16.26.22.png [ 31.36 KiB | Viewed 6362 times ]


Wait while the firmware downloads.

Attachment:
Snap 2013-01-24 at 16.27.02.png
Snap 2013-01-24 at 16.27.02.png [ 59.31 KiB | Viewed 6362 times ]


Once finished, cycle the power on the terminal, fix your computers IP address settings and enable any disabled Ethernet ports in control panel on the PC.

_________________
Best Regards,

Beijer Electronics, Inc.
Ron Lloyd | Applications Engineer


 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 1 post ] 

All times are UTC - 7 hours [ DST ]


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to: